Product Overview

The Total Light TL-SL200-CB is a low-profile 12V LED step light designed to provide controlled, downward-facing illumination across steps, risers, walls, stonework and other flat outdoor surfaces. Its solid-brass housing extends approximately 9 inches across the mounting surface while projecting less than 3/4 inch, helping the fixture maintain a discreet architectural appearance after installation. The shielded face directs light toward the surface below to reduce direct glare and visible hot spots around stairs, patios, seating walls and frequently traveled outdoor areas.

An integrated LED light source removes the need to purchase a separate lamp. The fixture provides selectable 2700K or 3000K color-temperature settings and supports remote dimming, on/off control and color-temperature selection when used with the compatible Total Light TL-REMOTE, sold separately. This lets the installer adjust the completed lighting scene without removing the fixture from the mounting surface. Its 12V design allows the step light to operate as part of a properly sized low-voltage landscape-lighting system.

The TL-SL200-CB features solid-brass construction with a Classic Brass finish, an IP67 ingress-protection rating, ETL certification and lifetime residential and commercial warranties. Stainless-steel mounting screws are included. Installation requires only the appropriate mounting holes and a small wire-access opening, although the installer should confirm that the mounting surface, fasteners, wiring method and low-voltage power supply are suitable for the project. Refer to the SKU-specific specification sheet below for the current dimensional drawing and additional technical information.

View the compatible Total Light TL-REMOTE

Key Features

• Integrated LED step light for 12V low-voltage systems
• Selectable 2700K or 3000K color temperature
• Remote dimming, color-temperature selection and on/off control with the optional TL-REMOTE
• Four LED diodes
• Low-profile housing projects less than 3/4 inch from the mounting surface
• Approximately 9-inch fixture width for broad downward illumination
• Shielded face helps reduce direct glare and visible hot spots
• Solid-brass construction with a Classic Brass finish
• IP67 ingress-protection rating
• Stainless-steel mounting screws included
• ETL certified
• Lifetime residential and commercial warranties

Common Uses

• Step risers and stair approaches
• Decks, patios and outdoor landings
• Retaining and seating walls
• Brick, stone and masonry surfaces
• Outdoor kitchens and entertaining areas
• Columns, posts and architectural walls
• Low-level walkway and guidance lighting
• Flat surfaces requiring controlled downward illumination

Technical Specifications

• Model: TL-SL200-CB
• Fixture Type: Surface-mounted LED step light
• Operating Voltage: 12V low voltage
• Light Source: Integrated LED
• LED Configuration: Four LED diodes
• Color Temperature: Selectable 2700K or 3000K
• Control Compatibility: Remote dimming, CCT selection and on/off control with TL-REMOTE, sold separately
• Material: Solid brass
• Finish: Classic Brass
• Ingress Protection: IP67
• Certification: ETL
• UPC: 00810016891369
• Residential Warranty: Lifetime
• Commercial Warranty: Lifetime

Dimensions

• Fixture Width: Approximately 9 inches
• Fixture Projection: Less than 3/4 inch from the mounting surface

Refer to the current specification sheet for the complete dimensional drawing.

Integrated LED and Control Compatibility

The TL-SL200-CB includes an integrated LED light source, so no separate lamp is required. Its selectable 2700K and 3000K settings allow the fixture to coordinate with warmer or neutral-warm landscape-lighting designs. The compatible Total Light TL-REMOTE is sold separately and provides access to remote dimming, color-temperature selection and on/off control.

View the compatible Total Light TL-REMOTE

Installation and Planning Notes

• Install only as part of a compatible 12V low-voltage lighting system.
• Mount to a flat, stable surface capable of supporting the fixture.
• Position the shielded face so illumination is directed toward the intended tread, walkway or architectural surface.
• Use the included stainless-steel screws only when they are suitable for the mounting material.
• Use surface-appropriate anchors or alternate fasteners when required.
• Provide a small wire-access opening behind the fixture and use approved outdoor connections.
• Confirm transformer capacity and voltage drop for the complete lighting layout.
• Use the separately sold TL-REMOTE to adjust dimming, color temperature and on/off control.
• Follow applicable electrical and building requirements.
• Refer to the specification sheet for the current dimensional drawing and additional product details.

What Is Included

• One Total Light TL-SL200-CB step-light fixture
• Integrated LED light source
• Solid-brass housing in Classic Brass
• Stainless-steel mounting screws

What Is Not Included

• Total Light TL-REMOTE
• Low-voltage transformer
• Main landscape-lighting cable and wire connectors
• Surface-specific anchors or additional installation materials

Product Specification Sheet

Open the current specification sheet for the complete dimensional drawing and additional product information.

Frequently Asked Questions

Does the TL-SL200-CB require a separate lamp?

No. This step light includes an integrated LED light source.

Can the color temperature be changed?

Yes. The fixture supports selectable 2700K and 3000K color-temperature settings. The compatible TL-REMOTE, sold separately, provides remote color-temperature selection.

Is the TL-REMOTE included?

No. The TL-REMOTE is sold separately and provides remote dimming, on/off control and 2700K/3000K selection.

Where can this step light be installed?

Common locations include step risers, walls, stonework, deck and patio areas, retaining walls, outdoor kitchens and other flat surfaces that benefit from controlled downward illumination.

Why Choose Total Light?

The TL-SL200-CB combines a slim solid-brass housing, integrated LED output, selectable color temperature and optional remote control in one low-voltage fixture. Its shielded design supports comfortable step and architectural lighting while the IP67 rating, ETL certification and lifetime warranties provide documented support for residential and commercial installations.