Proudly fly your support for the Strokes Fighting Spokes wherever you go with a cool flag! 25% of all proceeds from these flags are donated to support Dan Zimmerman and Spokes Fighting Strokes. With eye-catching and attention getting reflective, you'll get noticed day and night! Hi Vis tassel and two-piece fiberglass pole included.

ADDITIONAL INFO

• These flags maintain their cool even at high speeds. The unique shape is both attention getting and tuned for just the right amount of flap, even at high speeds. No noisy flappity flap, just a gentle, attention getting back and forth. An additional hi-vis tassel can be attached at the bottom of the flag.
• Poles are black fiberglass for strength and to blend in with your other black accessories. Poles are a combined 70 inches (1.8m) long and separate in the middle for transport. Special silicone rubber grip keeps tubes from separating until you tell them to. Poles are stiff enough a light can be attached, we have an optional mount for that. The end of the bottom pole is 6mm in diameter to fit any flag mount (6mm is just slightly smaller than 1/4 inch).
• Every flag comes with a Hi Vis tassel. You can add a second one if you wish, there are two grommets, one at the top of the flag and one at the bottom.
• We also offer our own very versatile flag mounts if you need a good place to mount it.
• Made from highly weather and UV resistant outdoor polyester for long life and excellent resistance to fading. Poles are solid fiberglass, with two 36in (0.9m) long sections. Sections are joined by a special carbon fiber ferrule with a silicone rubber grip collar to keep things together until you want them apart. Poles are 1/4in diameter, with an option for a 1.75in (4.5cm) 6mm section on the bottom end of the lower pole for compatibility with 6mm flag mounts. Flag is shaped for visual contrast, aerodynamics, and controlled flapping, even at high speeds. 3M reflectives used are rated for high effectiveness even when wet.
• The upper tip of the lower pole is red to indicate the end that is inserted into the upper pole. Slide the tapered red tip through the silicone grip collar until it is firmly seated in the ferrule on the lower end of the upper pole. Insert the bottom end of the lower pole into your flag mount. You can typically put your flag into the tube that runs down the side of your seat. Some trikes, such as ICE trikes, have a hole in the plastic top cap for that purpose. Others, like TerraTrikes, may require you to drill a slightly larger than 1/4 inch (about 6.35mm) hole in the top cap. Other trikes, such as Catrikes, come with a 6mm flag mount back on the rear dropout. The rear racks on HP trikes have flag mounts in them.
• The silicone gripper collar is designed to keep your poles from separating under all but the most extreme conditions. To separate the poles, pinch the collar around the lower pole until it wrinkles a little bit. This will break the suction and allow you to gently twist the lower pole out. If you try to just yank the pole out, the collar will tighten and grip even more. Pushing the collar up with a fingernail will also relax the collar and cause it to release it's grip on the pole.
• There is a plastic clip near the top of the flag. Inside the flag, on the end of the pole, there is a cap that cushions the end of the pole. The cap can't get past the clip. If you want to remove the flag from the pole for any reason, gently pry the clip off and slide the flag off the pole. The cap is designed to catch on the bottom of the flag as a backup. You will need to wriggle and twist to get the cap out the bottom of the flag.
• If it gets dirty, wipe your flag down with a cloth or old toothbrush dampened with soap and water. The colors are colorfast and UV resistant and cannot be scrubbed off.
• You can install the Hi Vis tassel using the grommets at the top and bottom of the flag. If you are running one tassel, we recommend putting it at the top of the flag. One tassel comes standard with every flag.