This premium underfloor insulation is designed for vans and campervans, helping to reduce road noise and improve thermal insulation beneath your floor.

Why Use Underfloor Insulation?

Underfloor insulation helps create a quieter, warmer and more comfortable van by adding an insulating layer between the metal floor and your ply lining. It helps reduce road noise and vibration from below, while also improving heat retention to make the van feel less cold underfoot. It also helps smooth out minor imperfections in the metal floor beneath, giving your ply flooring a neater and more even base to sit on.

💡 Bundle kits: If you’ve landed here looking to insulate a full van, our van insulation kit is usually the better option, as it works out better value than buying everything separately.

Key Features

Designed for under ply flooring – Sits neatly beneath your floor layer
Reduces road noise – Helps cut down sound and vibration from the road below
Improves thermal insulation – Helps make your van warmer and more comfortable underfoot
Smooths minor floor imperfections – Creates a more even surface beneath ply flooring
Gold aluminium foil vapour control barrier – Helps reduce the risk of moisture build-up
Lightweight – Easy to handle and install
Flame retardant – Added safety for your van build
Includes enough High Temperature Spray Adhesive – One complete kit!

Technical details

Width: 1 metre
Length: Choice of length
Thickness: 5mm

Not sure which size you need?

Van Size	Approx. Floor Coverage Needed	Recommended Underfloor Insulation	Van Size Examples
HALF Camper	4sqm	1 x 4m roll	VW Caddy, Ford Transit Connect
MEDIUM - Short Wheel Base	5sqm	1 x 6m roll	VW Transporter T4/T5/T6/T6.1, Ford Transit Custom, Vivaro, Trafic, Primastar
MEDIUM - Long Wheel Base	6sqm	1 x 6m roll	VW Transporter T4/T5/T6/T6.1, Ford Transit Custom, Vivaro, Trafic, Primastar
LARGE	7-8sqm	2 x 4m rolls	VW Crafter, MAN TGE, Mercedes Sprinter, Fiat Ducato

How to fit underfloor insulation in a campervan

What you'll need:

Gold Underfloor Insulation
High-temperature spray adhesive
Utility knife
Tape measure
Degreaser + clean cloth

Tip: Install in dry, room-temperature conditions for best adhesion.

1. Prepare the Floor: Sweep / vacuum any dust and debris. Wipe the metal floor with degreaser and allow to dry fully. A clean surface is important for the adhesive to stick.

2. Roll out & Cut the Insulation:

Roll the insulation out across the entire floor area. Allow it to settle flat for a moment - this makes cutting easier.
Roughly position it into place.
Cut around obstacles such as wheel arches, steps, seat mounts, or any floor reinforcements. Use a sharp utility knife and make slow, controlled cuts. Lift or fold the insulation back slightly where needed so you can see the outline clearly.
Check your fit frequently.
As you cut, press the sheet down temporarily to make sure it settles nicely into floor contours.
Trim the edges for a snug finish.
Once everything is sitting flat, tidy up the perimeter by trimming flush to the walls or ribs.

Tip: Large sheets can be bulky. If the piece becomes difficult to handle, don’t hesitate to cut it into two sections to make fitting easier - it won’t affect performance.

If handling large pieces feels difficult, you can also cut the insulation into smaller, more manageable sections. This makes it easier to position the material accurately, especially if installing it without any help. Smaller offcuts can also be used to neatly fill any remaining gaps.

3. Apply Adhesive & Fix the Insulation

Work in manageable sections so the glue stays tacky.
Spray a thin, even coat of adhesive on both the metal floor and the back of the insulation.
Allow 30–60 seconds for the adhesive to go tacky.
Press the insulation firmly into place.
Smooth from one edge outward to avoid air pockets.
Ensure it is fully stuck down over ridges and corners.

4. Add Your Flooring

Lay plywood or your finished floor covering directly on top.
If using wooden battens, place them on top of the insulation (not on the bare metal) to maintain continuous insulation.