- All-in-one control: Integrated 24V driver + in-wall dimmer in a single device.
- Installer-friendly power: Up to 100W Class 2, 24V DC output for low voltage LEDs.
- Professional dimming: Smooth low-voltage dimming, power-failure memory, and UL listed safety.
The HitLights 24 Volt EZDim Driver and Dimmer Switch 100 Watt is an all-in-one 24V LED driver and wall dimmer that powers and controls low voltage LED lighting from a single device in a standard electrical box. It accepts 120VAC input and delivers 24V DC output for 24V LED strip lighting and other low voltage fixtures.
The 24V EZDim provides up to 100 watts of Class 2, 24V DC power for LED loads, supporting roughly 4.1 amps when fully loaded. For longevity, many installers size the connected load to about 80 percent of capacity. EZDim combines an LED driver and wall dimmer into a single UL listed device, reducing the need for separate transformers and compatibility checks between remote drivers and wall controls.
- Combines 120VAC input driver and 24V DC dimmer in one integrated unit
- Fits a standard single-gang recessed electrical box with no derating when ganging units
- Dimming is PWM based and adjustable from full output down to about 10 percent
- Built-in protection for short circuit, thermal conditions, and over-voltage with ≤0.5W standby power
The unit is IP30 rated for dry, indoor locations and requires a neutral connection along with line and load conductors. It is suitable for 24V LED strip lights, under-cabinet runs, shelving accents, coves, niches, and other architectural lighting where a clean in-wall solution is preferred.
Three interchangeable faceplates are included in glossy white, glossy light almond, and glossy dark brown, allowing the dimmer to blend with common interior finishes. A wall plate is not included, so standard decorator plates can be selected to match existing devices. The EZDim carries FCC and UL Class 2 listings and a six-year warranty for added project confidence.
Unlike traditional setups that use a separate wall dimmer and remote low voltage driver, this integrated design simplifies wiring, minimizes installation time, and reduces potential failure points in LED strip lighting systems.
WHAT'S INCLUDED:
-
1 × HitLights EZDim 24V 100W in-wall dimmer driver switch
A: The HitLights 24V EZDim Driver and Dimmer Switch is an integrated 24V LED driver and in-wall dimmer for low voltage LED lighting. It converts 120VAC to 24V DC and provides local dimming control for 24V LED strip lights and similar fixtures from a single standard wall box.
Q: Who is this 24V EZDim driver and dimmer designed for?
A: This model is designed for electricians, contractors, and advanced DIY users installing 24V LED strip lighting in residential or light commercial spaces. It suits projects where a hardwired, code-friendly wall control is preferred over plug-in power supplies or remote dimmers, especially in kitchens, living areas, and architectural accent lighting.
Q: How does the EZDim driver and dimmer switch work?
A: The EZDim accepts 120VAC line voltage and internally converts it to regulated 24V DC while controlling output with PWM dimming. The front dimmer interface provides on/off switching and smooth adjustment from full brightness down to approximately 10 percent, with power-failure memory that restores the previous level after power is interrupted.
Q: What are the electrical specifications of the 24V 100W EZDim model?
A: The 24V 100W EZDim delivers up to 100 watts (about 4.1 amps) of 24V DC Class 2 output from a 120VAC, 50/60Hz input. It offers ≥0.9 power factor at full load, ≤20 percent THD, and ≤0.5 watt standby power, with integrated short circuit, thermal, and over-voltage protection for LED strip applications.
Q: Is the EZDim compatible with 24V LED strip lights and other fixtures?
A: Yes, the 24V EZDim is intended for 24V DC LED loads, including 24V LED strip lights and other compatible low voltage fixtures. As long as the total load does not exceed 100 watts and wiring follows Class 2 guidelines, it can support under-cabinet runs, shelving, coves, niches, and similar installations.
Q: What faceplates and accessories are included with this EZDim unit?
A: Each EZDim unit ships with three interchangeable faceplates in glossy white, glossy light almond, and glossy dark brown to match different interior color schemes. A wall plate is not included, so standard decorator plates can be chosen to coordinate with existing switches and receptacles in the space.
Q: Can the EZDim be used outdoors or in damp locations?
A: No, this EZDim driver and dimmer is IP30 rated and intended for dry, indoor locations only. It should be installed in a standard recessed single-gang electrical box in accordance with local codes, and not placed in wet, damp, or exposed environments.
SHIPPING DETAILS:
- Standard Shipping (3-5 Days) - Shipping cutoff 3pm (PST).
- FREE ground shipping (UPS or FedEx) on orders of $199 or more
- Standard Shipping: Flat Rate $9.99 - Cutoff 3PM (PST)
- 2-Day Shipping: Rate Based on Weight - Cutoff 2PM (PST)
- Overnight Shipping: Rate Based on Weight - Cutoff 2PM (PST)